Case Farmall 70JX / 75JX / 80JX / 90JX / 100JX / 110JX tractors, repair e-manual
About the manual
Displacement: 3.4 / 3.9 / 4.5 / 4.9 L.
Power: 70 / 75 / 80 / 90 / 100 / 110 hp
In the manual you will find
- Step-by-step guide to repair various components and assemblies
- Self-care and maintenance instructions
- Car design and prevention information
- Information for a trip to the service station, if self-repair is not possible
About the manual
Displacement: 3.4 / 3.9 / 4.5 / 4.9 L.
Power: 70 / 75 / 80 / 90 / 100 / 110 hp
In the manual you will find
- Step-by-step guide to repair various components and assemblies
- Self-care and maintenance instructions
- Car design and prevention information
- Information for a trip to the service station, if self-repair is not possible
Content
General
- Engine
- General specification
- Injection pump calibration data
- General specifications
- Tightening torques
- Tools
- Lubrication and cooling system diagrams
- Fault diagnosis
- Engine Radiator
- Crankshaft front oil seal
- Coolant pump
- Cooling system thermostat
- Bosch injection pump
- Injectors
- Valve clearance
- Coolant pump
- Compression test
Clutch
- General specifications
- Tightening torques
- Tools
- Clutch troubleshooting
- Adjustment of the main and PTO clutch control linkage
Gearbox
- Main data
- Tightening torques
- Tools
- Section views
- Description and operation
- Fault diagnosis
Transmission of motion
Front mechanical transmission
- Main data
- Tightening torques
- Tools
- Cross-sectional views
- Description and operation
- Front axle
- Steering knuckle bearing pins
- Stub axle adjustment
- Wheel hub bearing adjustment
- Bevel drive adjustment
- Front axle differential
- Leading drive wheels toe
Rear mechanical transmission
- Main data
- Tightening torques
- Special tools
- Cross-sectional views
- Transmission-gearbox casing
- Differential lock engagement sleeve
- Determining the bevel pinion positioning adjustment ring
- Adjusting the taper roller bearings for the bevel pinion shaft
- Adjusting the bearings and checking the backlash
- Differential pinion and side gear backlash adjustment
Power take-off
- Main specification
- Tools
- Torque settings
- Sectional drawings
- Description and operation
- Troubleshooting
- Bench
Brakes
- Main data
- Tightening torques
- Cross-sectional views
- Description and operation
- Tools - troubleshooting
- Front brake
- Service brake
- Bleeding air from the front braking system
- Parking brake
Hydraulic systems
- Main specification
- Tightening torques
- Tools
- Cross-sectional views
- Description and operation
- Hydraulic circuit
- Description and operation of lift phases
- Fault diagnosis
- Hydraulic lift
- Linkage
- Pressure relief valve
- Lift control valve
- Lift pump
Steering
- Principal data
- Tightening torques
- Section views
- Hydraulic diagram
- Operation
- Fault diagnosis
- Tools
- Hydrostatic steering control valve
- Hydrostatic steering oil pump
- Steering cylinder
Axle and wheels
- Principal data
- Sectional views
- Torque settings
- Equipment - fault diagnosis
- Wheel hub disassembly
- Stub axle overhaul
- Checking wheel alignment
Auxiliary equipment
- Safety instructions
- General characteristics
- Equipment
- Operating principles
- Fault diagnosis
- Cab controls
- Main components of the cab air conditioning system
- Refrigerant recovery-recycling and evacuation-charging stations
- Drying recharging and checking cooling
- Receiver-drier
- Condenser
- Compressor
- Compressor drive belt tension
Electrical system
- Instruments
- Starting system
- Charging system
- Battery
- Electrical circuits
Cab


