Iveco Daily since 2006,, repair e-manual (in Russian), volume 1
About the manual
Engine types: diesel
In the manual you will find
- Instructions for repair of various vehicle components
- Information on self-service car
- Information on the design of the car and how to prevent failure
- The information for the trip to the service station, if the self-repair is impossible
About the manual
Engine types: diesel
In the manual you will find
- Instructions for repair of various vehicle components
- Information on self-service car
- Information on the design of the car and how to prevent failure
- The information for the trip to the service station, if the self-repair is impossible
Contents
Operating instructions
- Electronically controlled air suspension ECAS
- Pneumatic suspension (can only be installed on 35C / 65C models)
Starting the engine and moving the car
- Immobilizer
- Car keys
- Code card
- Emergency start engine ignition switch position
- Enabling the immobilizer
- Disabling the immobilizer
- Starting the engine
- Engine shutdown
- Centralized door locking system (if installed)
- Cold weather starting
- Self-diagnosis of car systems
- Centralized door locking system with electronic alarm (if installed)
- AGILE gearbox (if fitted)
- Display vehicle operation with automatic transmission
- Speed programming
- Using the power take-off (if equipped)
- Fault signaling
- Starting the engine by towing the vehicle
- Engaging the rear axle differential lock
- Anti-lock braking system (ABSJ / pressure limiting valve (EBD) / tire adhesion monitor (ABD)
- ESP8 - electronic stability control system
- Grade hold system
- ABS8 (if installed)
- Cruise control (if installed)
- Power take-off (if included in the transmission)
- Works performed by the driver independently
- Precautions when working with electronic control units installed in the vehicle
- Mandatory instructions
- Car towing
- Driver checks
- Before every trip
- Scheduled maintenance
Specifications
- Engine
Maintenance
- Car maintenance schedule
- Inspection and maintenance checklist
- Maintenance operations
- M1 maintenance
- Maintenance M2
- Maintenance EP1
- Maintenance EP2
- EPZ maintenance
- Maintenance T1 (at the beginning of each spring)
- Maintenance T2 (at the beginning of each winter)
- Technical maintenance of technical specifications
- Maintenance T4
- Under-dash fuse and relay box
- Under-dash fuse and relay box (EURO 4, EURO 5, NATURAJ POWER)
- Fuse and relay box in the engine compartment (EURO 4, EURO 5. NATURAL POWER)
- Fuse and relay box in the engine compartment (EURO 4) (EURO 4, EURO 5, NATURAL POWER) outdoor unit
- Engine compartment fuse and relay box (EURO 5)
- Additional fuse box (engine compartment)
- Additional fuse box in the engine compartment (EURO 5)
- Engine compartment fuse and relay box (NATURAL POWER)
- Additional fuse box in the engine compartment (NATURAL POWER)
Menu control panel
- Display message
- BASE version display
- BASE version menu structure - engine start (ignition switch ON)
- Dashboard COMFORT version
- COMFORT version display
- Diesel particulate filter (particulate filter for diesel engines)
- F1A engine
- Engine removal / installation
- Replacing the timing belt
- Replacing electrically operated fuel injectors
- Exhaust toxicity, smoke and noise
- F1AE0 engine
- Diagnostics
- Basic operations with an engine not removed from the vehicle
- Tightening torques for threaded connections
- Longitudinal section of the engine with horn system
- Cross section of an engine with horn system
- Repair of the F1A engine
- Dismantling the engine at the stand
- Renovation work
- Cylinder block
- Crankshaft
- Engine assembly
- Installing the rear oil seal
- Flywheel
- Assembly of pistons with connecting rods
- Pistons
- Rods
- Cylinder head
- Valves
- Valve guides
- Valve seats
- Valve springs
- Swing levers (rockers) - pushers
- Installing the cylinder head
- Gas distribution system
- Camshaft
- Adjusting the tension of the air conditioning compressor drive belt
- Camshaft position sensor
- Crankshaft speed sensor
- Lubrication system
- Oil and vacuum pump assembly (GPOD)
- Oil pressure reducing valve
- Oil filter
- Heat exchanger modine
- Crankcase ventilation and oil separator
- Cooling system
- Fan clutch
- Water pump
- Thermostat
- Turbocharging
- Turbocharger
- Repair
- Pressure reducing valve
- Exhaust gas recirculation
- Power system
- Electronically controlled high pressure fuel injection (MS 6.3)
- System operation
- Hydraulic part of the fuel system
- Fuel pump
- Fuel lines
- High pressure fuel pump
- High pressure fuel pump device
- Pressure regulator valve
- Mechanical booster pump
- Hydraulic accumulator (RAMP)
- Pressure reducing valve
- Electrically operated injectors
- Electrical / electronic components
- Electronic control unit edc 16 for EUR04 engines
- Sensors
- Actuators
- Regulators with pulse width modulation (PWM)
- Differences of EURO4 motors
- Exhaust Gas Recirculation (EGR)
- Control solenoid valve
- Mass air flow sensor (DMRV)
- Throttle assembly (body)
- EGR heat exchanger
- Exhaust gas cleaning system (particulate filter)
- Particulate filter regeneration system
- Muffler with catalytic particulate filter
- Fuel system
F1C engine
- While the engine has not yet been removed from the vehicle
- Electrically operated injectors
- High pressure fuel pump SRZ
- High pressure fuel pipes
- Fuel rail components
- Removal and engine installation
- Withdrawal
- Installation
- Checks
- Removing air from the mains (pumping)
- Replacing the A / C compressor drive belt (tensioner option)
- Replacing the power steering belt and generator
- Replacing the water pump
- Replacing the high pressure fuel pump (injection pump)
- Replacing the power steering pump
- Replacing the front crankshaft oil seal and front engine cover gasket
- Replacing the vacuum and oil pump assembly
- Replacing the rear crankshaft oil seal
- Replacing fuel injectors
- Removing / installing cylinder head
- General view of the engine
- Sticker
- Cylinder block marking
- Characteristic curves
- Technical data
- Special tools
- Tightening torques of threaded connections, НМ
- F1C engine repair
- Dismantling the engine at the workbench
- Repair
- Cylinder block
- Table of measurements of the diameters of the main and connecting rod journals
- Crankshaft 188 Checking the crankshaft
- First main journal (timing side)
- Root necks No. 2, No. 4
- Root collar No. 3
- Rear neck (flywheel side)
- Connecting rod journals
- Installing the engine
- Flywheel
- Pistons with connecting rods
- Pistons
- 540830 connecting rods
- Bushings
- Dismantling the cylinder head
- Valves
- Valve guides
- Valve seats
- Valve springs
- Rockers and hydraulic supports
- Cylinder head assembly
- Gas distribution mechanism drive
- Crankshaft locking
- Gas distribution mechanism drive
- Lubrication system
- General information
- Oil system operation
- Oil / Vacuum pump assembly
- Oil filter
- Heat exchanger
- Crankcase ventilation system
Cooling system
- Description
- Electromagnetic clutch
- Water pump
- Thermostat
- Turbocharging
- Repair
- Bypass valve
- Turbocharger GARRET GT 2256 TC variable turbine geometry (F1C E0481 V engine - 166 hp)
- Repair
Fuel system
Electronically controlled high pressure battery power system (EDC 16)
- General information
- System operation
- Fuel system operation
- Fine fuel filter
- Booster fuel pump
- Fuel filter
- High pressure fuel pump (TNVD)
- Pressure regulator
- Mechanical booster pump
- Electro-controlled (electromechanical) fuel injectors
- Electrical and electronic components
- Electronic control unit (ECM) EDC 16
- Electronic control unit for glow plug power supply
- Glow plugs
- Sensors
- Actuators (executive devices)
- F1С EURO-4 engines
- Specifications
- Exhaust gas recirculation (EGR) heat exchanger removal / installation
- Exhaust system
- Removing the muffler
- Removing the catalyst and filter
- Installation
Clutch
- Description
- Diagnostics
- Technical data
- Removing and installing clutch
- Removing and installing release bearing
- Clutch actuator
- Hydraulic clutch actuator
- Removing-installing pedal board
- Pedal board
- Clutch with automatic wear compensation - complete with gearbox 6 AS'300 VD
- Removing and installing clutch with automatic wear compensation
Gearbox
- Diagnostics
- Removal-installation of the checkpoint
- Gearbox control
- Gearbox 5 S 300
- Mechanism of selection and inclusion of gears
- Safety devices
- Technical data (specifications)
- 5 S 300 gearbox repair
- Gearbox
- Disassembly of the main shaft
- Input shaft
- Disassembly of the transfer (intermediate) shaft
- Checks
- Main shaft assembly
- Stems - forks - selector - carrier
- Gearbox assembly
- Gearbox 6 S 400 O.D
- Technical data (specifications)
- Tightening torques
- 6 S 400 gearbox repair
- Gearbox
- Disassembly of the gearbox
- Removing the bearings from the rear cover
- Removing bearings from gearbox housing
- Disassembly of the main shaft
- Disassembly of the gearbox input shaft
- Dismantling the intermediate shaft
- Synchronizers
- Installing the intermediate (transfer) shaft
- Main shaft assembly
- Stems - forks - selector - carrier
- Gearbox assembly
- Automatic transmission 6 S 400 A O.D
- Main functions of the system
- Vehicle restraint system on a slope
- Management system structure
- Technical data
- Tightening torques for threaded connections
- Diagnostics
- MODUS connection - IT 2000 - E.A.SY
- Removal and installation of the checkpoint
- Gearbox repair
- Body-gearbox wiring harness
- Gearbox cable harness
- Calibration
Power take-off
- Technical data
- Assembly instructions
- Electric actuator for power take-off
Cardan shafts
- Technical data
- 4x2 models
- 4x2 models
- Removing and installing propeller shaft
Rear axle
- Troubleshooting
- Rear axle NDA RS
- Removing / installing rear axle
- Description
- Technical data
- Rear axle NDA RG
- Removing / installing rear axle
- Description
- Technical data
- Rear axle 450511
- Rear axle technical data 450511
- Removing / installing rear axle
- Description
- Technical data
- Rear axle repair
- Build
- Wheel hub repair
- Differential repair operations
Front axle
- Diagnostics
- 5817 front axle
- Description
- Technical data
- Removing and installing front axle
- 5817 front axle repair
- Removing and installing a wheel hub
- Removing / installing steering knuckle
- 5818 front axle
- Description
- Technical data
- 5818 Front axle repair
- Replacing the driving wheel of the ABS sensor
- Installation
- Removing and installing a wheel hub
- 5819 front axle
- Description
- Front suspension 5819
- Technical data
- 5819 front suspension repair
- 5823 Front axle
- Description
- Technical data
- Removal and installation of bridge 5823
- Repair of the front suspension 5823
- Removing and installing a wheel hub
- Replacing the driving wheel of the ABS sensor
- Installation
- Replacing the wheel stud
Camber and toe
- Description
- Camber angle
- Angle of lateral inclination of the axle of rotation of wheels
- Caster angle of the wheel axis
- Wheel alignment
- Wheel alignment angles
- Checking wheel alignment
Mechanical suspension
- Mechanical front suspension
- Description
- Cross leaf spring (models 29 L - 35 S - 35 С)
- Specifications
- Front single leaf spring
- Anti-roll bar
- Front shock absorbers
- Tools
- Tightening torques for threaded connections (NM)
- Renovation work
- Suspension repair
- Suspension arms
- Replacing the suspension arm bushings
- Anti-roll bar model 29 L - 35 S
- Front shocks 29 L - 35 S
- Leaf spring suspension
- Torsion bar suspension (front axles 5819 model 35 С - 40 С - 45 С - 50 С)
- Repair of jet suspension rods
- Replacing the swivel tips
- Torsion bars
- Replacing silent blocks and bumpers
- Replacing the swivel tips
- Adjusting the pre-tension bar
- Front anti-roll bar 35 C - 40 C - 45 C - 50 C
- Front shock absorbers 35 C - 40 C - 45 C - 50 C
- Suspension repair
- Replacing the swivel tips
- Torsion bars
- Replacing rubber grommets
- Rear suspension
- Technical data
- Tools
- Tightening torques for threaded connections (NM)
- Rear springs
- Renovation work
- Spring assembly
- Replacing bushings
- Rear shock absorbers
- Rear anti-roll bar
Pneumatic suspension
- Diagnostics
- Rear air suspension - VB-TECHNIEK model flashing code
- Rear air suspension - WABCO model
- Flashing code
- General part
- WABCO air suspension (for models 29 L - 35 S)
- Technical data
- WABCO Pneumatic System (ECAS)
- Electronic control
- How the air suspension works
- Models without ABS
- ABS models
- Automatic chassis trim, raise and lower
- Main components of the system
- Air supply unit
- Electronic control unit
- Clearance sensor
- Pneumatic element (air spring)
- Load sensing valve
- Rear suspension repair
- Leaf spring
- Rear shock absorbers
- Rear anti-roll bar
- Panhard's jet thrust